 |
| |
 |
| |
| M1A | M14 RIFLE ARMORERS TOOLS |
Receiver/ barrel Timing Gage
For use with the M1, M14/M1A rifles. Used with 2 12” or longer Steel rules or a Precision level (not included)
P/N 200-01 | 
Handguard Clip Pliers
For use with the M1, M14/M1A rifles. Used to remove and install the Handguard clip.
P/N 200-05 | 
Bedding Fixture
For use with the M1, M14/M1A rifles. Used with your standard bedding tools for single or double stage bedding. (not included)
P/N 200-06 |
 |
Gas Cylinder Alinement Gage
For use with the M14/M1A rifle. Used to check alinement fo gas cylinder to gas port in barrel.
P/N 223-02 |
|
|
 |
Stock Liner Screw Wrench
Used to Install or remove stock liner screws, fits a Magnetic tip screw driver w/1/4 Hex Drive or a socket wrench.
P/N 223-04 |
|
| |
|
|
 |
Bolt Roller Greaser
For use with the M14/M1A rifle. Used to Grease the bolt roller, operator tool, fit’s in Buttstock with other cleaning equipment. As seen in the American Rifleman.
P/N 223-03 |
|
|
 |
Bolt Roller Greaser
Armorers version
For use with the M14/M1A rifle. Used to Grease the bolt roller. T-handle for high volume use.
P/N 223-03A |
|
| M1 GARAND |
Operating Rod Spring Gage
For use with the M1 rifle. Used to verify the strength of the operating rod spring. Requires a trigger pull gage that can read at least 18 lbs. (not included)
P/N 222-01 |
Gas Cylinder Plug Valve Fixture
For use with the M1 rifle. Used to hold valve open to clean, or for refinishing.
P/N 222-03 |
Timing Gage
For use with the M1 rifle. Used to gage bolt release timing. This is an exact duplicate of the U.S. Army WW2 issue gage.
P/N 222-04 |
M1 Garand Gas Cylinder Gage
This gage allows you to determine the quality of your M1 Rifles gas cylinder. Made to the exact spec of the G.I. Issue gage. Made from tool steel and hardened to 60Rc.
P/N 222-05 | 
M1 Garand Throat Erosion Gage
This tool allows you to gage the throat wear in your M1 rifle. Made to the exact spec of the G.I. Issue gage. Made from tool steel and hardened to 60Rc.
P/N 222-07 |
|
| M16, M4, AR-15, AR-10 ARMORERS TOOLS |
| |
|
|  Rear Sight Instalation Tool
For use with the M16A2/AR-15A2 rifles. Used to install A2 style Adjustable rear sights.
P/N 249-01 |
| REMINGTON M700 |
|
| |
|
 | Chambering Gage
This tool allows bullet proof chambering of rifle barrels.
Comes complete with a dial indicator and instructions, removes the guess work and inconsistency of using a regular depth gage. Reads directly to the exact number you need. U. S. Pat. #5170169.
P/N 200-11 |
| |
 | Remington Action V-block
Use this precision ground block when you are using piloted tooling to re-thread the receiver, lap the lugs, open the mounting holes or are doing any type of mill work. Made from 4140 and hardened to 60Rc.
P/N 306-65 |
|
| | | |
 | Firing pin protrusion gage
Check the exact length of your firing pins protrusion with this direct reading gage. Comes complete with a dial indicator and instructions.
P/N 200-12 |
| |
 | Recoil Lug Alinement Fixture
Alines recoil lug properly when installing barrel. Works with Chandler/Badger Ordnance Maximized Recoil Lug, also works with Standard Remington recoil lug, Dakota Arms M97 Hunter and the Beretta Mato.
P/N 306-04 |
|
|
| |
|
